单选题 Outlets along the side walls and the center of the ceiling divide the air for symmetrical supply.

A、 空气沿着侧壁和顶板中央流出,分开并同时供气.
B、 出口在侧壁边缘和顶板中央分离空气,以便全面供气.
C、 沿侧壁和顶板中央的出口将空气分开均匀供气.
下载APP答题
由4l***gz提供 分享 举报 纠错

相关试题

单选题 Format and layout is to be determined by the CAP producer, recognizing that it is desirable that the format and layout be similar to the producer's existing documents.

A、格式和排版由CAP编写者决定,要认识到其格式和排版最好与编写者现有文件相似.
B、格式和排版由CAP生产者提议,其批准需经过与现有文件格式和排版的对比.
C、格式和排版由CAP生产者定义,并预期与现有的文件格式和排版保持一致.

单选题 In some cases, extension of inspection frequencies may be possible if the data suggests that the onset of fatigue problems occurs at a greater number of flight hours than initially predicted.

A、在某些情况下,延长检查频率可能会对疲劳检查造成不足,从长远讲会造成实际飞行小时数低于最初预测.
B、在某些情况下,如果数据表明疲劳问题发生在比最初预测的飞行小时数更多,则可以放缓检查频率.
C、在某些情况下,延长实际飞行小时将影响疲劳检查,因此会造成维修检查的小时数远低于最初预测.

单选题 This can cause a deterioration of the mechanical properties of the assembly.

A、这会导致组件的机械性能的恶化.
B、这会导致组件的机械部件的变形.
C、这会导致组件的机械装置碰撞.

单选题 The assembly extends through the casing assemblies and is connected to the telescopic control assembly.

A、组件延伸至壳体,安装并连接在通信控制组件上.
B、组件延伸至壳体组件,并与伸缩控制组件相连.
C、组件延伸至壳体组件,并与通讯控制组件相连.

单选题 Loosen the air valve nut one or two turns to slowly release the air pressure. Drain hydraulic fluid by inverting shock strut or removing check valve.

A、拧松气阀螺母一两圈,慢慢释放气压.通过反转减震支柱或拆除单向活门排放液压油.
B、拧松气阀螺母一两圈释放气压.排放减震柱液压油可以通过拆除单向活门进行.
C、拧松气阀螺母一两圈缓慢释放液压.液力油排放从减震柱或单向活门处进行.

单选题 Outside Air Temperature is the free air static temperature, obtained either from inflight temperature indications or ground meteorological sources, adjusted for instrument error and compressibility effects.

A、机外空气温度是指自然空气温度,可以从飞行中的机上温度显示器读取,也可以从地面气象站获取,经过压缩系数调整,来校准仪表误差.
B、机外空气温度是静止大气温度,可以从机上温度显示器读取,也可以从地面气象源获得,并根据仪表误差和压缩效应调整.
C、机外空气温度是静止大气温度,可以从机上温度显示器读取,也可以从地面气象台获取,为减少误差需要调整仪表错误和压缩系数效应.

单选题 The circulation of the air in the components is such that the temperature for specific component is not out of the limit.

A、该部件中的空气循环使得特定部件的温度不超限.
B、某些部件的温度不超限因此该部件中的空气能够流动.
C、该部件中的空气的旋转和特殊部件的温度均不超限.

单选题 Turbine blade tip clearances decrease when the turbine case is cooled.

A、当压气机匣被冷却后,压气机叶片间距变小.
B、当涡轮机匣被冷却后,涡轮叶尖距变小.
C、当涡轮机匣被冷却后,涡轮叶片间距变小.